Let’s try a cold start on the Ford 800 tractor... -6c or 21f

FORD 800...Let's diagnose the tapping sound in the engine drop the oil and inspect the air filter

The Stone Setter

Ford 800...Let's place back the oil pan..Push rod and rocker cover all cleaned and painted

Ford 800..Let's adjust the clutch pedal and remove the seat assembly for some repairs

Ford 800..Let's fill the oil up check for leaks !!!Special Guest Appearance!!!

Steering arm in for the Ford 800 lets fit it on and lets tackle the wiring but there's issues :(

Another attempt at the Ford 800 wiring....This was just a day of everything going wrong OMG

Ford 800....Let's drain the rad for a new heat gauge install

Ford 800...Adjust the wicked toe in and I was beat on a 5/16 broken bolt what the......

Ford 800..Let's install the refurbished fuel tank and work on the exhaust system & carburetor remove

Thought we had a new Carburetor for the Ford 800....Hit a major road block

Build a new fuel line for the Ford 800.Test for leaks...Had a big FAILURE...All needs to come apart

We're going to replace a part we already installed on the Ford 800.

Let's see if the Ford 800 will lift this heavy disc.......Hopefully

Ford 800..This fuel system just does not want to work for us. more leaks :(

Today we received in some interesting parts for the Ford 800...BIG job

Let's do a cold and hot compression test on the Ford 800

Ford 800...Lets make and solder on a new rad overflow tube...Test run but something happened :(

New parts for the Ford 800 in.Some cleaning and painting to do and install some sleeve compound

Ford 800..Brand new Cylinder Head lets clean and prime

Ford 800..Let's work on the head..Might have a major problem with a valve guide.My bad.Could be junk

FORD 800...Decided to change the intake/exhaust manifold as well....Check it out

Ford 800...Lets start the engine assembly process

Ford 800....Installing the new head and torquing to spec

Ford 800 lets install the rockers and cover as well as the New Manifold

Ford 800..Lets tear off the front end axle and get into the front main seal...What a mess

Ford 800 parts cleaned up and painted...Let's reassemble on the tractor...Also a fan mail package

Ford 800 install the new push rods but have hit a big snag...Need 1 part

Ford 800...We have parts for the rockers...Let's try this again

Ford 800....Lets get the front axle back together and back on the tractor...Weld'er solid!

Ford 800..Cooling system work...Install the new radiator and water pump

Ford 800 New ignition system install and Test Run....Then I did something Really Really stupid

Ford 800 Fuel tank Install...Interesting quirk...Then a full warm up and drive

Ford 800….Plowing the garden..Gave it a good test out...hitch Lift arm issue though.

Ford 800 Exhaust change and hood button up..Again something happened to the engine

Lets take a look at the electronic ignition for the ford 800 and some other parts we ordered

Ford 800 Electronic ignition install then Fire the old points and condenser to the MOON

Ford 800 lets pull off the rear top plate and see why the 3pt hitch wont lift high enough

Ford 800 front wheel hub and bearing removal for inspection

All painted up..Lets pack and reinstall the wheel bearings. FORD 800

Let's pull the pistons and rods out and measure some rings Ford 800

Ford 800...Piston and connecting rod rebuild...Measurement of the new rings in the new sleeves

The Ford 800 is 90% back together...Will it even run again?? Lets find out!!

Let's check the valve lash cold then hot on the Ford 800

Well I just went ahead and did it... Expensive part!!! Ford 800

Let's get the fuel tank together and mounted...Plumbing in a new fuel separator Ford 800

Some more assembly of the repainted parts for the Ford 800

Have some parts for the Ford 800 painted and ready to install....(Hood and and steering box)

While we have it apart lets take off the Steering box and check it out FORD 800

Ford 800 console removal for painting

Ford 800 fuel tank fill up and check for leaks...LETS FIRE IT UP and test the new steering out